Write firmware using password - Revision history

Sfptotal at 08:36, 20 July 2016

2016-07-20T08:36:05Z

2016-07-20T08:35:50Z

2016-07-20T08:35:37Z

2016-07-20T08:34:48Z

2016-07-20T08:33:58Z

2016-07-20T08:31:14Z

2016-07-20T08:29:41Z

2016-07-20T08:29:32Z

2016-07-20T08:28:59Z

2016-07-20T08:27:24Z

@@ Line 7: / Line 7: @@
 ''' Scripts -> Set password'''
-:: [[File:Sfptotal-set-password.jpg]]
+[[File:Sfptotal-set-password.jpg]]
 Push OK button to save changes or Cancel to close the window.
@@ Line 15: / Line 15: @@
 '''Scripts -> Enter transceiver password -> Enable'''
-:: [[File:Sfptotal-enter-password.jpg]]
+[[File:Sfptotal-enter-password.jpg]]
 You need to reset the scripts before writing with a password.
@@ Line 23: / Line 23: @@
 After the password is set, the programmer will write a password before performing the firmware write.
-:: [[File:SFPTotal_Writing_Button.jpg]]
+[[File:SFPTotal_Writing_Button.jpg]]
 == Notes ==

@@ Line 7: / Line 7: @@
 ''' Scripts -> Set password'''
-[[File:Sfptotal-set-password.jpg]]
+:: [[File:Sfptotal-set-password.jpg]]
 Push OK button to save changes or Cancel to close the window.
@@ Line 15: / Line 15: @@
 '''Scripts -> Enter transceiver password -> Enable'''
-[[File:Sfptotal-enter-password.jpg]]
+:: [[File:Sfptotal-enter-password.jpg]]
 You need to reset the scripts before writing with a password.

← Older revision		Revision as of 08:35, 20 July 2016
Line 22:		Line 22:

	After the password is set, the programmer will write a password before performing the firmware write.		After the password is set, the programmer will write a password before performing the firmware write.
		+
		+	:: [[File:SFPTotal_Writing_Button.jpg]]

	== Notes ==		== Notes ==

@@ Line 11: / Line 11: @@
 Push OK button to save changes or Cancel to close the window.
-By default, the software produces a write firmware without using a password. You need to set a flag to activate the account with a password:
+By default, the software produces a write firmware without using a password. You need to set a flag '''Enable''' to activate the writing with a password:
 '''Scripts -> Enter transceiver password -> Enable'''

@@ Line 14: / Line 14: @@
 '''Scripts -> Enter transceiver password -> Enable'''
 [[File:Sfptotal-enter-password.jpg]]
 ''' Scripts -> Reset script'''
 == Notes ==

← Older revision		Revision as of 08:31, 20 July 2016
Line 16:		Line 16:

	You need to reset the scripts before writing with a password.		You need to reset the scripts before writing with a password.
		+
		+	[[File:Sfptotal-enter-password.jpg]]

	''' Scripts -> Reset script'''		''' Scripts -> Reset script'''

@@ Line 1: / Line 1: @@
 The software supports write firmware using a password and provides a simple interface.
-Software supports password length of 4 bytes (eight symbols HEX codes).
+Software supports password length of 4 bytes (eight symbols HEX code).
 You can set a password that will be used to unlock the module firmware before recording. To set a password, and set the memory area to enter the password follow:

← Older revision		Revision as of 08:28, 20 July 2016
Line 22:		Line 22:

	# To use this function module must support the unlocking of the table A0h when entering a password.		# To use this function module must support the unlocking of the table A0h when entering a password.
		+	# Address enter the password may differ depending on the module type and vendor-specific solutions.

← Older revision		Revision as of 08:27, 20 July 2016
Line 21:		Line 21:
	== Notes ==		== Notes ==

−	* To use this function module must support the unlocking of the table A0h when entering a password.	+	# To use this function module must support the unlocking of the table A0h when entering a password.