Write firmware to the transceiver's memory - Revision history

Sfptotal: /* Programming transceivers according to MSA standards */

2015-11-20T21:14:15Z

‎Programming transceivers according to MSA standards

2015-11-20T21:13:29Z

‎Programming transceivers according to MSA standards

2015-11-20T13:09:59Z

2015-11-20T13:08:57Z

2015-11-20T13:08:02Z

‎Programming using scripts

2015-11-20T13:07:11Z

‎Programming using scripts

2015-11-20T13:04:57Z

2015-11-20T13:01:40Z

2015-11-20T13:00:28Z

‎Programming using scripts

2015-11-20T12:59:25Z

‎Programming using scripts

@@ Line 30: / Line 30: @@
 :: [[File:SFPTotal Write firmware.jpg]]
-Before recording firmware recommend that you save backup copies of the firmware of the available address space of the transceiver.
+Before writing recommend that you save backup copies firmware of the available address space of the transceiver.
 Also recommend enable logging for saving all images that will be read from the memory of the transceiver to case of situation when you accidentally overwrite the memory of the transceiver or improper configuration will be necessary to restore the original firmware.

← Older revision		Revision as of 21:13, 20 November 2015
Line 29:		Line 29:

	:: [[File:SFPTotal Write firmware.jpg]]		:: [[File:SFPTotal Write firmware.jpg]]
		+
		+	Before recording firmware recommend that you save backup copies of the firmware of the available address space of the transceiver.
		+
		+	Also recommend enable logging for saving all images that will be read from the memory of the transceiver to case of situation when you accidentally overwrite the memory of the transceiver or improper configuration will be necessary to restore the original firmware.

	== Programming transceivers using scripts ==		== Programming transceivers using scripts ==

@@ Line 47: / Line 47: @@
 : '''You should pay attention to the fact that after implementation of that algorithm there is no software verification of the writing.'''
-: If the writing was successful, the contents of the firmware in the '''Table''' will not be changed upon completion of the [[Reading transceiver's memory|reading operation]].
+: If the writing was successful, the contents of firmware in the '''Table''' will not be changed upon completion of the [[Reading transceiver's memory|reading operation]].
 == Notes ==
 # The basic set of scripts for writing the firmware to the memory of the transceivers from different manufacturers is supplied with the program.

@@ Line 3: / Line 3: @@
 * '''Programming using scripts''' for write-protected transceivers and transceivers with non-standart reprogramm algorithm.
-== Programming according to MSA standards ==
+== Programming transceivers according to MSA standards ==
 If  transceiver supports writing the memory according to the MSA standards for the selected type of module, software sends a command to the programming board that implements the algorithm of writing into the memory.
@@ Line 30: / Line 30: @@
 :: [[File:SFPTotal Write firmware.jpg]]
-== Programming using scripts ==
+== Programming transceivers using scripts ==
 When the first option does not work for the selected transceiver, writing into memory is made with a special set of commands (scripts) that are sent to the programmer for a

@@ Line 47: / Line 47: @@
 : '''You should pay attention to the fact that after implementation of that algorithm there is no software verification of the writing.'''
-: If the writing was successful, the contents of the firmware in the '''Table''' will not be changed upon completion of the reading operation.
+: If the writing was successful, the contents of the firmware in the '''Table''' will not be changed upon completion of the [[Reading transceiver's memory|reading operation]].
 == Notes ==
 # The basic set of scripts for writing the firmware to the memory of the transceivers from different manufacturers is supplied with the program.

@@ Line 35: / Line 35: @@
 realization of custom writing algorithm, supported bytransceiver.
-In the tab '''BATCH LOADER -> Select instruction''' to specify path to the file with algorithm of writing.
+: 1. In the tab '''BATCH LOADER'''  click to the button  '''Select instruction''' to specify path to the file with algorithm of writing.
-Make sure that the tab TABLE contain the correct firmware for writing. Check the [[Validation firmware checksum|firmware checksum]].
+:: [[File:SFPTotal_Writing_using_scripts.jpg]]
-Next step press button for writing the transceivers memory.
+: 2. Make sure that the tab TABLE contain the correct firmware for writing. Check the [[Validation firmware checksum|firmware checksum]].
 :: [[File:SFPTotal_Writing_Button.jpg]]

← Older revision		Revision as of 13:00, 20 November 2015
Line 37:		Line 37:
	In the tab '''BATCH LOADER -> Select instruction''' to specify path to the file with algorithm of writing.		In the tab '''BATCH LOADER -> Select instruction''' to specify path to the file with algorithm of writing.

		+	You should pay attention to the fact that after implementation of that algorithm there is no software verification of the writing.

	The basic set of scripts for writing the firmware to the memory of the transceivers from different manufacturers is supplied with the program.		The basic set of scripts for writing the firmware to the memory of the transceivers from different manufacturers is supplied with the program.