Reading transceiver's memory - Revision history

Sfptotal at 12:23, 20 November 2015

2015-11-20T12:23:15Z

2015-11-20T12:21:06Z

2015-11-20T12:18:29Z

2015-11-20T12:17:42Z

2015-11-20T12:11:08Z

2015-11-20T12:10:23Z

2015-11-20T12:03:56Z

2015-11-20T12:01:06Z

2015-11-20T11:59:44Z

2015-11-20T11:57:22Z

← Older revision		Revision as of 12:23, 20 November 2015
Line 15:		Line 15:

	: [[File:SFPTotal Reading transceivers.jpg]]		: [[File:SFPTotal Reading transceivers.jpg]]
		+

	If reading successful, then program will show message '''READ OK'''.		If reading successful, then program will show message '''READ OK'''.

@@ Line 2: / Line 2: @@
 To perform reading of the transceiver’s memory it is necessary to:
-# Connect the PG series programmer to a computer and run the program [[SFPTotal Wizard]], or just connect the device, if the program is already running.
+: 1. Connect the PG series programmer to a computer and run the program [[SFPTotal Wizard]], or just connect the device, if the program is already running.
-# Connect the transceiver to the programmer port.
+: 2. Connect the transceiver to the programmer port.
-# Choose type of your transceiver (Module Type) and a memory table for reading (Select table).
+: 3. Choose type of your transceiver (Module Type) and a memory table for reading (Select table).
-# Click the button of reading the transceiver's memory.
-# The program display a response by programming board in the history of operations and exports the data in Table tab.
+: [[File:SFPTotal_Module_type_selector.jpg|Select module type and memory table]]
 If reading successful, then program will show message '''READ OK'''.
-[[File:SFPTotal Reading transceivers.jpg]]
 == Notes ==
 # Recommended to enable logging for saving all images that will be read from the memory of the transceiver to case of situation when  you accidentally overwrite the memory of the transceiver or improper configuration will be necessary to restore the original firmware.

@@ Line 2: / Line 2: @@
 To perform reading of the transceiver’s memory it is necessary to:
-# Connect the PG series programmer to a computer and run the program, or just connect the device, if the program is already running.
+# Connect the PG series programmer to a computer and run the program [[SFPTotal Wizard]], or just connect the device, if the program is already running.
 # Connect the transceiver to the programmer port.
-# Choose type of your transceiver (Module Type) and a momory table for reading (Select table).
+# Choose type of your transceiver (Module Type) and a memory table for reading (Select table).
-# Click the button of reading the transceiver's memory:
+# Click the button of reading the transceiver's memory.
 # The program display a response by programming board in the history of operations and exports the data in Table tab.

@@ Line 3: / Line 3: @@
 # Connect the PG series programmer to a computer and run the program, or just connect the device, if the program is already running.
 # Choose type of your transceiver (Module Type) and a momory table for reading (Select table).
 # Click the button of reading the transceiver's memory:
@@ Line 8: / Line 9: @@
 If reading successful, then program will show message '''READ OK'''.
 == Notes ==
 # Recommended to enable logging for saving all images that will be read from the memory of the transceiver to case of situation when  you accidentally overwrite the memory of the transceiver or improper configuration will be necessary to restore the original firmware.

@@ Line 3: / Line 3: @@
 # Connect the PG series programmer to a computer and run the program, or just connect the device, if the program is already running.
-# Choose type of your transceiver (Module Type) and a table for reading (Select table).
+# Choose type of your transceiver (Module Type) and a momory table for reading (Select table).
 # Click the button of reading the transceiver's memory:
 # The program display a response by programming board in the history of operations and exports the data in Table tab.

@@ Line 4: / Line 4: @@
 # Choose type of your transceiver (Module Type) and a table for reading (Select table).
-;; [[File:SFPTotal_Module_type_selector.jpg]]
+[[File:SFPTotal_Module_type_selector.jpg]]
 # Click the button of reading the transceiver's memory:
 # The program display a response by programming board in the history of operations and exports the data in Table tab.
-;; [[File:SFPTotal Reading transceivers.jpg]]
+::[[File:SFPTotal Reading transceivers.jpg]]
 If reading successful, then program will show message '''READ OK'''.